10 Big Reasons to Choose a MAGNATRAC
More Stable than a Wheeled Tractor
A MAGNATRAC® steel tracks and undercarriage provide a heavy anchor down low. Wheeled vehicles carry their weight up high on tires, which are essentially bags of air. The lower center of gravity of a MAGNATRAC® lets you get the job done safely on slope conditions far too dangerous for most wheeled vehicles.
Many Tractors Try to Dig…We Actually Do It
A compact wheeled tractor contacts the ground on less than 260 sq. in. The MH series MAGNATRAC® puts over 770 sq. in. on the ground! That means you keep pushing when they start spinning. There is even enough traction to drive a 48″ loader bucket into the ground in the MH Series MAGNATRACS.
Much Harder to Get Stuck
More ground contact on a MAGNATRAC® means the tracks big surface area “floats” on top of mud, sand, snow and other difficult surfaces, while wheels sink in and spin, digging themselves into a hole.
Zero Turn Capability and No Shifting Gears
The MAGNATRAC® turns 360 degrees in half the space. Because you can rotate our tracks in opposite directions at the same time, a Magnatrac turns in it’s own length. The MH Series MAGNATRAC® turns in just over 6 ft. A comparably powered compact tractor requires more than twice the space – over 13 ft. of clear space to turn around. No shifting gears, means no messing around with clutches or other controls! Instant power to forward and reverse make a MAGNATRAC® a pleasure to drive for everyone!
No Flat Tires to Worry About
Rubber tires are easily cut, bruised, punctured, and go flat in storage. Even rubber tracks take a beating in sharp rocks and debris. Our all steel tracks are 100% blowout proof. They’re impervious to just about anything: sharp rocks, glass, scrap steel, nails, hot materials, weight…even time! So you can clear brush or a work site with no worries of unseen objects damaging tires.
Stronger Track Design With TCP™ Technology
TCP™ stands for Tandem Chain Path. This trademarked track design has 7x greater sprocket support compared to a single sprocket design. The drive behind the MAGNATRAC® TCP™ system is the matched sprockets of the rear drive and front idler sprocket. Simultaneously engaging both track chains, provides redundancy in case of debris interference.
Compact and Powerful
Any tractor can be compact, but powerful is another story. We’re built for power with our low torque design! Compact enough to fit though the woods to pull large logs, small enough to be easily trailer-ed and compact enough to back-fill in tight areas or fit through smaller residential gates. You can even fly the compact & powerful MAGNATRAC® into remote locations with a helicopter & still get the job done!
Free Technical Support for Life
We’re here to help you! We have been selling our products factory direct for over 49 years. This has ensured no middleman markup or hassles, and has kept us close to our customers and their needs. We have learned a lot about what our equipment, as well as what others are capable of doing. Free phone technical support is always included with every new purchase. So if you have some tough projects in mind give us a call, and we’ll help you decide which products and attachments would be right for you.
Not Just Built in America…Made in America
We design all of the Struck products. They’re not cheap foreign imports, and we build them ourselves from start to finish right here in Cedarburg, Wisconsin, America’s heartland. We do business in the millions of dollars, but we’re no mass-producer by a long shot. We employ a trusty crew made up of individuals who have been with us an average of 15 years. Our small, hard-working company builds every Struck product with care, pride and personal attention. That’s getting nearly impossible to find these days. We are committed to providing exceptional Quality, Service, and Value in every part of our business!
New Technology Improves Quality, Reduces Price
“Make it better.” This simple concept has been the key to our success for over four decades. This attitude applies to every aspect of production…all the way from cutting metal to painting parts. Utilizing CNC lathes, robotic welding, automated punching, and abrasive water jet cutting technologies we can design, fabricate, and finish new designs quickly and efficiently. This means more savings passed on to you! These advances make a better product that we’re proud to put our name on.